Pengontrolan Kecepatan Aliran Vortex Berbasis Arduino Sebagai Metoda Pemisah Campuran Serbuk Tembaga dan Aluminium

Authors

  • Fico Trianda Ravelli Universitas Andalas
  • Firman Ridwan Andalas University

DOI:

https://doi.org/10.25077/metal.3.1.51-58.2019

Keywords:

Flow Rate, separator, mining, vortex flow

Abstract

Several methods have been developed to separate gold from alluvial using the principle of density. Density is used as a basic concept in material separation. One of the supporting methods that can be used to utilize the vortex flow as a separation medium. With vortex flow, two materials of different density can be separated through lift force. This study aims to determine the effect of vortex flow velocity on its ability to separate two different types of density material. Aluminum and Copper powders are used as test materials with a powder size of 18-200 mesh. The tests are carried out with a variation of 10 flow rates with water as a fluid. The results showed that Aluminum and Copper can be optimally separated at the flow rate (165.25-167.77) ml/s. While for the most effective effectiveness of Al separation is the flow rate (163.22-168.87) ml / s and copper separation at the flow rate (83.5-85) ml/s.

References

Y. S. Helmi Guntoro, Erik Haritman, “RANCANG BANGUN MAGNETIC DOOR LOCK MENGGUNAKAN KEYPAD DAN SOLENOID BERBASIS MIKROKONTROLER ARDUINO UNO,†Electrans, vol. 12, pp. 10, 2013.

"Pengertian Ukuran Mesh dan Konversinya," 03 Desember 2018, 2018. G. D. Gordon K. Van Vleck, Don L. Blubaugh, Michael Silva, James F. Davis, "Placer Gold Recovery Methods," C. D. o. C. D. o. M. a. Geology, ed., California Department of Conservation Division of Mines and Geology, 1986.

M. P. Jones, “A Continuous, laboratory-size density separator for granular materials,†1965.

Y. S. Helmi Guntoro, Erik Haritman, “RANCANG BANGUN MAGNETIC DOOR LOCK MENGGUNAKAN KEYPAD DAN SOLENOID BERBASIS MIKROKONTROLER ARDUINO UNO,†Electrans, vol. 12, pp. 10, 2013.

H. T. Sularso, Pompa & Kompresor, 7 ed., Jakarta: PT Pradnya Paramita, 2000.

M. S. Prof. Dr. Abd Wahid Wahab, Dr. Nursiah La Nafie, M.Sc, Metode Pemisahan dan Pengukuran 2 (Spektrometri dan Elektrofotometri), Makassar: Program Studi Kimia Fakultas Matematika dan Ilmu Pengetahuan Alam Universitas Hasanuddin, 2014.

Salman, “Penangkapan Partikel Timah dari Alluvial Tambang Timah Dengan Metode Vortex,†Jurusan Teknik Mesin Fakultas Teknik Universitas Andalas, Padang, 2011.

T. S. Muhammad Budi Nur Rahman, “PENGARUH SUDUT WATER SPRAYER DAN TEKANAN AIR DALAM SPRAYER PUMP TERHADAP HASIL SERBUK ALUMUNIUM PADA PROSES ATOMISASI AIR,†Ilmiah Semesta Teknika, vol. 9, pp. 13, 2006.

A. Maulana, "Mengenal Arduino Uno Lebih Rinci," aozon.blogspot.com, 2014.

A. Munandar. "Liguid Crystal Display (LCD) 16 x 2," 08 Desember, 2018.

Downloads

Additional Files

Published

2019-07-08

How to Cite

Ravelli, F. T., & Ridwan, F. (2019). Pengontrolan Kecepatan Aliran Vortex Berbasis Arduino Sebagai Metoda Pemisah Campuran Serbuk Tembaga dan Aluminium. METAL: Jurnal Sistem Mekanik Dan Termal, 3(1), 51–58. https://doi.org/10.25077/metal.3.1.51-58.2019

Issue

Vol. 3 No. 1 (2019)

Section

Articles

License

Please find the rights and licenses in Jurnal Sistem Mekanik dan Termal (METAL).

1. License

Public use of the works published in this journal is bound to the Creative Commons Attribution license as currently displayed on Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License. In previous editions, our articles included incomplete licensing information. In the recent editions, we have corrected this to align with the appropriate license, the CC BY-NC-SA.

2. Author(s)' Warranties

The author(s) warrants that the article is original, written by the stated author(s), has never been published in any form anywhere before, contains no unlawful statements, does not infringe the rights of others, is subject to copyright that is vested exclusively in the author and free of any third-party rights, and that any necessary permissions to quote from other sources have been obtained by the author(s).

3. User Rights

METAL is actively supporting open access and open science initiatives; thus, METAL is disseminating articles published as freely as possible. Under the Creative Commons license, METAL permits users to copy, distribute, display, and perform the work for non-commercial purposes only. Users will also need to attribute authors and METAL when distributing works in the journal.

4. Rights of Authors

Authors retain the following rights:

  • Copyright, and other proprietary rights relating to the article, such as patent rights,
  • the right to use the substance of the article in future own works, including lectures and books,
  • the right to reproduce the article for own purposes,
  • the right to self-archive the article.

5. Co-Authorship

If the article was jointly prepared by other authors, by submitting his/her articles to METAL, it warrants that he/she has been authorized by all co-authors and agrees to inform his/her co-authors. Any internal disputes between authors will have to be cleared by themselves, and METAL will be notified of the result. METAL held no responsibilities whatsoever should any disputes arise and was freed from any responsibilities relating to the matter.

6. Miscellaneous

METAL will publish the article (or have it published) in the journal if the article's editorial process is successfully completed and METAL has become obligated to have the article published. METAL may adjust the article to a style of punctuation, spelling, capitalization, referencing, and usage that it deems appropriate. The author acknowledges that the article may be published so that it will be publicly accessible, and such access will be free of charge for the readers.


Most read articles by the same author(s)