Optimalisasi Dimensi Tabung Roasting Kopi Kapasitas 2 kg dengan Pendekatan Model Elemen Hingga



DOI: https://doi.org/10.25077/metal.6.1.1-7.2022

Author(s)

Dedi Suryadi (Universitas Bengkulu)
Bowo Anugrah (Universitas Bengkulu)
Ahmad Fauzan Suryono (Universitas Bengkulu)
Agus Suandi (Universitas Bengkulu)
Novalio Daratha (Universitas Bengkulu)

Abstract


Coffee roasting is an important process in the coffee industry that determines the quality of the coffee beverage obtained. The roasting process is carried out in a cylindrical tube having high temperature. Therefore, thermal stress on the cylindrical tube (drum) should be focused. In this paper, both appropriate materials selection and optimal dimension of the roaster drum are considered. Drum is given both thermal load of 200oC and a coffee load of 2 kg. Here, Aluminum Alloy 5083 and Stainless Steel 304 are analyzed as drum materials because these materials are recommended for foods. Finite element method is used for drum analysis with axisymmetric model. Moreover, optimal dimension of drum can be obtained by varying the length, diameter and thickness. The results show that Stainless Steel 304 is suitable material for drum under both thermal load and both thermal load of 200oC and a coffee load of 2 kg. While, dimensions of drum are length of 450 mm and diameter of 180 mm with thickness of drum larger than 1 mm.

Keywords


Coffee Roasting; Drum Material; Drum Dimensions; Finite Element Model; Thermal Stress

Full Text:

PDF

References


Badan Pusat Statistik, “Statistik perkebunan Indonesia”, Direktorat Jenderal Perkebunan, Jakarta, Indonesia, 2020.

Daywin, and Frans Jusuf Gozali, “Community service report: Designing the ergonomic roasting machine for coffee seed with additional electrical motor at Seduh Kopi coffee shop”, IOP Conference Series: Materials Science and Engineering, Vol. 852, No. 1, 2020.

I. Sofi’i, “Coffee’s Roaster Design Machine with Rotating Mixer,” J. Ilm. Tek. Pertan. Politek. Negeri Lampung, Vol. 6, No. 1, pp. 34–45, 2014.

Aggenstoss, J., Poisson, L., Kaegi, R., Perren, R. And Escher F., “Coffee roasting and aroma formation: Application of different time-temperature conditions”, J. Agric. Food Chem., Vol 56, pp. 5836–5846, 2008.

Chiang C. C., Wu D. Y., and Kang D. Y., “Detailed Simulation of Fluid Dynamics and Heat Transfer in Coffee Bean Roaster”, Journal of Food Process Engineering, vol. 40, No. 2, 2017.

Ogunjirin, O. A., Odeniyi, O. M., Olubo, A. S., Farounbi, A. J., Ola, O. A., and Adeleke, S. A., “Design and construction of an electrically powered coffee roasting machine. IOP”, Conference Series: Earth and Environmental Science. Vol.445, No. 1, 2020.

Alonso T. B., Hernández P. J. A., Sierra E. F., Schenker S., and Yeretzian, C., “Modeling and validation of heat and mass transfer in individual coffee beans during the coffee roasting process using computational fluid dynamics (CFD)”, Chimia, Vol. 67, No. 4, pp. 291-294, 2013.

Dutra E. R., Oliveira L. S., Franca A. S., Ferrez V. P., and Afonso, R. J., “A preliminary study on the feasibility of using the composition of coffee roasting exhaust gas for the determination of the degree of roast”, Journal of Food Engineering, Vol. 47, pp. 241–246, 2001.

Noda N. A., Suryadi D., Matsuda S., Takase Y., and Sano Y., “Proposal for New Hearth Roller Consisting of Ceramic Sleeve and Steel Shafts Used in the Heat Treat Furnace”, ISIJ International, Vol. 55, No. 11, pp. 2416.2425, 2015.

Khurmi R. S., Gupta J. K., “Machine Design”, Eurasia Publ House LTD Ram Nagar, New Delhi-110 055. 2005, Vol. 42, No. 3, pp. 59-59.

Patrick T. S., et. al., “Overview of Alluminium Alloy Mechanichal Properties During and After Fires”, Departement Of Mechanical Engineering Virginia Tech USA, 2015.

ASM Internasional, “Properties and Selection : Iron Steels and High Performance Alloy”, ASM Handbook, USA,1993, Volume 1.

Batubara A., Widyasanti A., Yusuf A., Uji “Kinerja dan Analisis Ekonomi Mesin Roasting Kopi (Studi Kasus di Taman Teknologi Pertanian Cikajang - Garut)”, Jurnal Teknotan, Vol. 13, No. 1, 2019.

Jhon H. L. IV anda Jhon H. L. V, “A Heat Transfer Textbook”. Philogiston Press, Cambrige Massachusetts, USA, 2019, Edisi 5.


StatisticsArticle Metrics

This article has been read : 415 times
PDF file viewed/downloaded : 197 times

Copyright (c) 2022 Dedi Suryadi

 


View METAL's Stats

 

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.