Pengaruh Media Pendingin pada Perlakuan Panas T6 terhadap Kekuatan Tarik dan Struktur Mikro Komposit Al6061-Pasir pantai



DOI: https://doi.org/10.25077/metal.5.2.51-59.2021

Author(s)

Hafidh Rawi Mufti (Universitas Sebelas Maret)
Hammar Ilham Akbar (Universitas Sebelas Maret)
Eko Surojo (Universitas Sebelas Maret)
Wibowo Wibowo (Universitas Sebelas Maret)
Teguh Triyono (Universitas Sebelas Maret)
Sukmaji Indro Cahyono (Universitas Sebelas Maret)
Nurul Muhayat (Universitas Sebelas Maret)
Triyono Triyono (Universitas Sebelas Maret)

Abstract


Al6061-sea sand composite was manufactured using the stir casting method and its mechanical properties were improved by heat treatment. The T6 heat treatment used to improve the mechanical properties of the composite consists of the following processes: solution heat treatment, quenching, and artificial aging. The solution heat treatment process was carried out at a temperature of 540oC for 6 hours. The quenching process was carried out with different quenching agents (water, oil, and 10% brine). The difference in quenching agents resulted in different cooling rates. After quenching, an artificial aging process was carried out at a temperature of 200 oC for 4 hours. The difference in cooling rate affects the hardness and tensile strength of the specimen. The high cooling rate results in an increase in the tensile strength of the specimen. This is due to the increase in cooling speed, the Mg2Si precipitates formed are smaller in size and located in the grains. The highest tensile strength of specimen (206.67 MPa) is obtained by using brine quenching agent.

Keywords


Al6061; sea sand; stir casting; quenching

Full Text:

PDF

References


S. S. Shinde, S. G. Kulkarni, and S. S. Kulkarni, “Manufacturing of Aluminium Matrix Composite Processing of Amc ’ S : Stir Casting :,” Int. J. Innov. Eng. Res. Technol. [IJIERT], vol. 2, no. 5, pp. 1–6, 2015.

S. Dhanesh, K. S. Kumar, N. K. M. Fayiz, L. Yohannan, and R. Sujith, “Recent developments in hybrid aluminium metal matrix composites: A review,” Mater. Today Proc., no. xxxx, 2020.

R. G. Bhandare and P. M. Sonawane, “Preparation of Aluminium Matrix Composite by Using Stir Casting Method,” Int. J. Eng. Adv. Technol., vol. 3, no. 2, pp. 61–65, 2013.

S. Gopalakrishnan and N. Murugan, “Production and wear characterisation of AA 6061 matrix titanium carbide particulate reinforced composite by enhanced stir casting method,” Compos. Part B Eng., vol. 43, no. 2, pp. 302–308, 2012.

A. S. Negi and T. Shanmugasundaram, “Hybrid particles dispersion strengthened aluminum metal matrix composite processed by stir casting,” Mater. Today Proc., no. xxxx, 2020.

V. Chak, H. Chattopadhyay, and T. L. Dora, “A review on fabrication methods, reinforcements and mechanical properties of aluminum matrix composites,” J. Manuf. Process., vol. 56. pp. 1059–1074, 2020.

J. Susanto, H. Seputro, and E. Santoso., “Analisa Pengaruh Variasi Media Pendingin Dan Waktu Aging Pada Perlakuan Panas T6 Terhadap Struktur Mikro,” J. Has. Penelit. LPPM Untag Surabaya, vol. 01, no. 02, pp. 227–238, 2016.

V. S. Vinod, S. Varghese, and B. Kuriakose, “Degradation behaviour of natural rubber-aluminium powder composites: Effect of heat, ozone and high energy radiation,” Polym. Degrad. Stab., vol. 75, no. 3, pp. 405–412, 2002.

G. S. balan, “Investigations on egg shell powder and glass fiber reinforced aluminium matrix composite,” Mater. Today Proc., no. xxxx, 2020.

B. P. KUMAR and A. K. BIRRU, “Microstructure and mechanical properties of aluminium metal matrix composites with addition of bamboo leaf ash by stir casting method,” Trans. Nonferrous Met. Soc. China (English Ed., vol. 27, no. 12, pp. 2555–2572, 2017.

H. I. Akbar, E. Surojo, and D. Ariawan, Effect of Sea Sand Content on Hardness of Novel Aluminium Metal Matrix Composite AA6061/Sea Sand. Springer Singapore, 2020.

Alimin, Maryono, and S. E. Putri, “Analisis Kandungan Mineral Pasir Pantai Losari Kota Makassar Menggunakan XRF dan XRD,” J. Fak. Mat. dan Ilmu Pengetah. Alam Univ. Negeri Makassar, pp. 19–23, 2013.

A. M. El-Sabbagh, M. Soliman, M. A. Taha, and H. Palkowski, “Effect of rolling and heat treatment on tensile behaviour of wrought Al-SiCp composites prepared by stir-casting,” J. Mater. Process. Technol., vol. 213, no. 10, pp. 1669–1681, 2013.

K. Rajkumar, P. Rajan, and J. M. A. Charles, “Microwave heat treatment on aluminium 6061 alloy-boron carbide composites,” Procedia Eng., vol. 86, pp. 34–41, 2014.

S. K. Tiwari, S. Soni, R. S. Rana, and A. Singh, “Effect of Heat Treatment on Mechanical Properties of Aluminium alloy-Fly ash Metal Matrix Composite,” Mater. Today Proc., vol. 4, no. 2, pp. 3458–3465, 2017.

H. I. Akbar, E. Surojo, D. Ariawan, and A. R. Prabowo, “Experimental study of quenching agents on Al6061–Al2O3 composite: Effects of quenching treatment to microstructure and hardness characteristics,” Results Eng., vol. 6, no. December 2019, p. 100105, 2020.

B. Benjunior, A. H. Ahmad, M. M. Rashidi, and M. S. Reza, “Effect of Different Cooling Rates Condition on Thermal Profile and Microstructure of Aluminium 6061,” Procedia Eng., vol. 184, pp. 298–305, 2017.

J. Mulyanti, “Pengaruh Temperatur Proses Aging Terhadap Karakteristik Material Komposit Logam Al-Sic Hasil Stircasting,” J. Kompetensi Tek., vol. 2, no. 2, pp. 95–104, 2011.

S. Y. Chen, K. H. Chen, G. S. Peng, X. Liang, and X. H. Chen, “Effect of quenching rate on microstructure and stress corrosion cracking of 7085 aluminum alloy,” Trans. Nonferrous Met. Soc. China (English Ed., vol. 22, no. 1, pp. 47–52, 2012.

S. Sharma, T. Nanda, and O. P. Pandey, “Investigation of T4 and T6 heat treatment on the wear properties of sillimanite reinforced LM30 aluminium alloy composites,” Wear, vol. 426–427, no. December 2018, pp. 27–36, 2019.

H. I. Akbar, E. Surojo, and D. Ariawan, “Effect of quenching agent on dimension stability of Al 6061-Al2O3 composite,” MATEC Web Conf., vol. 159, pp. 1–6, 2018.

W. D. Callister Jr, Materials Science and Engineering : An Introduction, 7th ed., vol. 26, no. 14. Utah: John Wiley & Sons Inc, 1991.

M. Engineering and S. Issn, “Tensile fractography of artificially aged Al6061-B4C composites Sathyashankara,” J. Mech. Eng. Sci., vol. 12, no. 3, pp. 3866–3875, 2018.

A. Hossain and A. S. W. Kurny, “Effect of Cu and Ni on the mechanical properties and fracture behavior of Al – Si – Mg cast alloys,” vol. 7, no. 2014, pp. 154–159, 2015.

A. Malekan, M. Emamy, J. Rassizadehghani, and A. R. Emami, “The effect of solution temperature on the microstructure and tensile properties of Al – 15 % Mg 2 Si composite,” Mater. Des., vol. 32, no. 5, pp. 2701–2709, 2011.

N. T. Aboulkhair, I. Maskery, C. Tuck, I. Ashcroft, and N. M. Everitt, “The microstructure and mechanical properties of selectively laser melted AlSi10Mg : the effect of a conventional T6-like heat treatment,” pp. 1–21.

H. Reza and J. Nodooshan, “Microstructure and Tensile Properties of Al-15wt % Mg2Si Composite after Hot Extrusion and Heat Treatment,” Key Eng. Materials, vol. 471-472, pp. 1171-1176, 2011.

N. Nasiri, M. Emamy, A. Malekan, and M. H. Norouzi, “Materials Science & Engineering A Microstructure and tensile properties of cast Al – 15 % Mg 2 Si composite : Effects of phosphorous addition and heat treatment,” Mater. Sci. Eng. A, vol. 556, pp. 446–453, 2012.

G. N. Ma, D. Wang, Z. Y. Liu, B. L. Xiao, and Z. Y. Ma, “An investigation on particle weakening in T6-treated SiC/Al–Zn–Mg–Cu composites,” Mater. Charact., vol. 158, no. September, 2019.

T. Zhang et al., “Heat treatment simulation investigation on the mechanical performance of the inter-critical heated affected zone (ICHAZ) in ship plate steel weld joint,” Appl. Ocean Res., vol. 101, no. June, p. 102237, 2020.


StatisticsArticle Metrics

This article has been read : 703 times
PDF file viewed/downloaded : 288 times

Copyright (c) 2021 Hafidh Rawi Mufti, Hammar Ilham Akbar, Eko Surojo, Wibowo Wibowo, Teguh Triyono, Sukmaji Indro Cahyono, Nurul Muhayat, Triyono Triyono

 


View METAL's Stats

 

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.