Pengaruh Sudut Geram dan Parameter Pemesinan Terhadap Keausan Tepi Pahat High Speed Steel (HSS) pada Proses Bubut Glass Fibre Reinforce Polymer (GFRP)



DOI: https://doi.org/10.25077/metal.2.1.40-46.2018

Author(s)

Muhammad Yusra Nusa (Universitas Andalas)
Firman Ridwan (Universitas Andalas)

Abstract


The high rate of tool wear is an obstacle in machining of GFRP material. This research was conducted to investigate turning behavior towards the occurrence of flank wear on HSS devices by varying machining parameters such as rake angle, spindle speed and feed rate. The GFRP of workpiece was made from resin as a matrix and the glass type Chopped Strand Mat as fiber. The rack angle of tool is varied to 5º, 10º, 15º, 20º.  Taguchi method was used to analized data experiments using orthogonal array L8. The experimental data shows that the spindle speed is the most influential parameter on flank wear with a S/N ratio of 4.10, followed by the feed rate with a S/N ratio of 3.08. Increasing rake angle can reduce wear, the smallest wear value was obtained at an angle of 20º.

Keywords


GFRP flank wear, rake angle, Spindle Speed, Feed Rate

Full Text:

PDF

References


J.Y. Sheikh Ahmad, "Machining of Polymer Composites,". The Petroleum Institute, Department of Mechanical Engineering, Abu Dhabi, United Arab Emirates,: Ed. Springer Science, 2009.

V.P. Astakhov, Tools (Geometry and Material) and Tool Wear, 2008.

T.J. Javier, "Analysis of tool wear after machining of Fibre Reinforced Polymers," Faculty of Mechanical and Industrial Engineering, Vienna university of technologi, Vienna, 2012.

T. Rochim, Teori & Teknologi Proses Pemesinan. Jurusan Teknik Mesin - ITB Bandung: High Education Development Support, 1993.

F. Kahwash, I. Shyha, and A. Maheri, "Machining Unidirectional Composites using Single-Point Tools: Analysis of Cutting Forces, Chip Formation and Surface Integrity," Procedia Engineering, vol. 132, pp. 569-576, 2015/01/01/ 2015.

K. Palanikumar, "Assessment of some factors influencing tool wear on the machining of glass fibre-reinforced plastics by coated cemented carbide tools," journal of materials processing technology 2 0 9 ( 2 0 0 9 ) 511–519, 2009.

V. G. Satyanarayana, Kosaraju, "Effect of Rake Angle and Feed Rate on Cutting Forces in an Orthogonal Turning Process," International Conference on Trends in Mechanical and Industrial Engineering (ICTMIE'2011) Dec., 2011 2011.

K.M.Usman, "Effect of Tool Rake Angle on Tool Life in Turning Tools," IJSER, vol. 3, 2012.

Α.Κ. Baldoukas, G.A. Demosthenous, A.E. Lontos, "Experimental Investigation of The Effect of Cutting Depth, Tool Rake Angle, and Workpiece Material Type on The Main Cutting Force During a Turning Process," ICMEN, vol. 3, 2008.

Khairusshima and I. S. S. Sharifah, "Study on Tool Wear During Milling CFRP under Dry and Chilled Air Machining," Procedia Engineering, vol. 184, pp. 78-89, 2017/01/01/ 2017.


StatisticsArticle Metrics

This article has been read : 369 times
PDF file viewed/downloaded : 242 times

Copyright (c) 2018 Muhammad Yusra Nusa

 


View METAL's Stats

 

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.